Difference between revisions of "Parts not supplied by Dynon"

From DynonDocs
Jump to: navigation, search
Line 20: Line 20:
 
** Specification:  
 
** Specification:  
 
** Example:  
 
** Example:  
* '''22 AWG Wire Selection''' - (TBD - kit of various colors of wire).
+
* '''Wire Selection''' - Kit of various colors of wire.
** Specification:  
+
** Specification: 22 AWG
 
** Example:  
 
** Example:  
* '''Adel Clamps (various diameters)''' - Required for mounting of various Dynon engine sensors.
+
* '''Adel Clamps ''' - Required for mounting of various Dynon engine sensors.
** Specification:  
+
** Specification: various diameters
 
** Example:  
 
** Example:  
* '''Connector Selection''' - (TBD - kit of various crimp-on connectors, including Butt Splice, FastOn, Ring Terminals).
+
* '''Crimp Connector Selection''' - Kit of various crimp-on connectors.
** Specification:
+
** Specification: Includes Butt Splice, FastOn, Ring Terminals
 
** Example:  
 
** Example:  
* '''Crush Washer (1/8", 5/8")''' - Required for installing Dynon Oil Temperature sensors.
+
* '''Crush Washer''' - Required for installing Dynon Oil Temperature sensors.
** Specification:  
+
** Specification: 1/8", 5/8"
 
** Example:  
 
** Example:  
* '''Resistor Selection''' - (TBD - kit of various resistor values, 10% tolerance, 1/2 watt power rating)
+
* '''Resistor Selection''' - Kit of various resistors.
** Specification:
+
** Specification: 10% minimum tolerance, 1/2 watt power rating minimum
 
** Example:  
 
** Example:  
 
* '''Teflon Tape''' - Required for installing various Dynon engine sensors.
 
* '''Teflon Tape''' - Required for installing various Dynon engine sensors.

Revision as of 09:42, 13 November 2008

Dynon Avionics supplies various parts, accessories, and sensors support the installation of its instruments. Many common, small parts - connectors, resistors, etc. are included in kits supplied with specific units and sensors. The complete list of all products available directly from Dynon Avionics is at http://www.dynonavionics.com/downloads/order_form.pdf.

But there are some parts that Dynon Avionics does not supply because of the vast range of aircraft that Dynon's instruments are installed in.

Dynon created this "Document Wiki" system as a dynamic set of documents that Dynon customers are invited and encouraged to help maintain, update, and enhance. Please contribute your favorite parts and suppliers that you have discovered that made your installation of Dynon instruments easier, faster, safer, less expensive, and more reliable.

Autopilot-related Parts


  • AP Disengage/Control Wheel Steering (CWS) Button - A push button is required for installation of the Dynon Autopilot (AP) to disengage the AP or to engage the AP in Control Wheel Steering (CWS) mode. It may be desirable to locate this button on the yoke instead of the panel.
    • Specification: Push Button Single Pole Normally Open (PB SP NO), minimum current rating 1 Amp (1A).
    • Example (for mounting on panel) - Aircraft Spruce P/N 11-00748.
  • AP74/HS34 Audio Level Adjustment Potentiometer - A variable resistor (potentiometer) is required to connect the audio output of the (AP74 {and HS34} into the aircraft's audio system. This potentiometer is typically only adjusted once, so we recommend that the potentiometer have a "short shaft" so that it can be tucked up under the panel, adjusted with a screwdriver, and then only rarely accessed.
    • Specification: Potentiometer with a short shaft, screwdriver slot, 10 Kilo Ohm (10 Kohm), 1/2 watt
    • Example -


Common Parts


  • 1/4" Inside Diameter Pneumatic Tubing (including adapters, clamps, etc.) - Required for connecting, routing, and securing pneumatic lines between Dynon EFIS pressure sensor ports and external ports.
    • Specification:
    • Example:
  • Wire Selection - Kit of various colors of wire.
    • Specification: 22 AWG
    • Example:
  • Adel Clamps - Required for mounting of various Dynon engine sensors.
    • Specification: various diameters
    • Example:
  • Crimp Connector Selection - Kit of various crimp-on connectors.
    • Specification: Includes Butt Splice, FastOn, Ring Terminals
    • Example:
  • Crush Washer - Required for installing Dynon Oil Temperature sensors.
    • Specification: 1/8", 5/8"
    • Example:
  • Resistor Selection - Kit of various resistors.
    • Specification: 10% minimum tolerance, 1/2 watt power rating minimum
    • Example:
  • Teflon Tape - Required for installing various Dynon engine sensors.
    • Specification:
    • Example:


Vendors