Difference between revisions of "HS34 Basic Operation Guide Text"

From DynonDocs
Jump to: navigation, search
(Proposed Text)
(Proposed Text)
Line 1: Line 1:
 
== Proposed Text ==
 
== Proposed Text ==
  
 +
*VALUE knob
 +
**When no menu is shown, pushing and holding it sets the barometer to 29.92 inHg.
 +
**When no menu is shown, turning it adjusts the barometer.
 +
**When in any menu which adjusts a numerical value, turning it value knob adjusts that value.
 +
**When in any menu which adjusts a numerical value, pushing it performs the same function as BACK.
 
*The light sensor can be configured in the EFIS > DIM menu to auto-dim all screens in a DSAB system
 
*The light sensor can be configured in the EFIS > DIM menu to auto-dim all screens in a DSAB system
*when no menu shown
+
*NAV/GPS status lights indicate currently active nav source.
**pushing and holding value knob sets baro to 29.92
+
*NAV SRC cycles through possible navigation sources in the order configured by the pilot.
**turning the value knob adjusts the barometer
+
*BRG SRC is used to configure bearing pointers on the HSI page. Exact behavior is dependent upon installed sources.
*when in any menu which adjusts a numerical value
 
**turning the value knob will adjust that value (pending verification)
 
**pushing the value knob will perform the same function as BACK
 
*NAV/GPS indicators
 
**indicate currently active nav source
 
*NAV SRC rotates through possible navigation sources in the order configured by the user
 
*BRG SRC is used to configure bearing pointers on the HSI page. Exact behavior is dependant upon installed sources.
 
 
*HEADING knob
 
*HEADING knob
**rotating will adjust the heading bug and will display the bug if it is not displayed
+
**Rotating it will adjust the heading bug and will display the bug if it is not displayed.
**tapping will sync heading bug to current heading
+
**Tapping it will sync heading bug to current heading.
**holding will toggle heading bug
+
**Holding it will toggle heading bug.
 
*COURSE knob
 
*COURSE knob
**rotating will adjust the course if allowed by the nav source (gps sends the course, nav radio user is tuning course)
+
**Rotating it will adjust the course if allowed by the nav source [gps sends the course, nav radio user is tuning course]
**tapping will sync course to current heading (again, if allowed)
+
**Tapping it will sync course to current heading (again, if allowed)
**holding will sync course to BTS
+
**Holding it will sync course to BTS
  
 
== Potential Additions ==
 
== Potential Additions ==

Revision as of 10:16, 20 August 2007

Proposed Text

  • VALUE knob
    • When no menu is shown, pushing and holding it sets the barometer to 29.92 inHg.
    • When no menu is shown, turning it adjusts the barometer.
    • When in any menu which adjusts a numerical value, turning it value knob adjusts that value.
    • When in any menu which adjusts a numerical value, pushing it performs the same function as BACK.
  • The light sensor can be configured in the EFIS > DIM menu to auto-dim all screens in a DSAB system
  • NAV/GPS status lights indicate currently active nav source.
  • NAV SRC cycles through possible navigation sources in the order configured by the pilot.
  • BRG SRC is used to configure bearing pointers on the HSI page. Exact behavior is dependent upon installed sources.
  • HEADING knob
    • Rotating it will adjust the heading bug and will display the bug if it is not displayed.
    • Tapping it will sync heading bug to current heading.
    • Holding it will toggle heading bug.
  • COURSE knob
    • Rotating it will adjust the course if allowed by the nav source [gps sends the course, nav radio user is tuning course]
    • Tapping it will sync course to current heading (again, if allowed)
    • Holding it will sync course to BTS

Potential Additions

Information about the "EFIS Provider" being the only unit on the bus providing EFIS info, the only one to be controlled by HS34, the one that needs to be on for DSAB to work.


Questions:

  • does value knob affect EMS values?
    • no, never.