Garmin 480 Wiring
Edit 11 Feb 2009 by Breister - We have two confirmations from people that they have gotten all functionality working as expected with v2.0 of the Garmin software or above.
NOTE!!! Version 2.3 of the Garmin software is the latest (and probably final) version, and you should GET THE UPGRADE!!! It is FREE - you just need to arrange with your local Garmin rep to get it done. Takes about 2-3 hours, and they provide you a new antenna which, together with the software, finally provides full WAAS / GPSS functionality.
On the GNS 480 side, only Input #2 accepts EFIS command. The HS34 has two sets of pins which will output ARINC, but that is only for convenience because both pairs output the exact same thing so you can use HS34 ARINC output #1 or #2. The only output setting is "Enable."
|CNX-80 / GNS 480 PLUS D100/D180 WITHOUT HS34 (Serial Only)|
|Garmin GNS 480||Dynon D100/D180|
|P5 (78 Pin)||30||Serial #8||Alt Enc / 1200||Vertical Fem D25||13||Serial Output||Alt Encoder / Format 1||Provides Baro info to 480|
|P1 (Main)||5||RS232 TxD1 (Output)||MAPCOM 9600||Vertical DB25||22 (Yellow)||Serial 1 Rx||Aviation 9600||Provides GPS Course - no vertical steering|
|P1 (Main)||4||RS232 RxD1 (Input)||SL 30||Vertical DB25||10 (Orange)||Serial 1 Tx||SL 30 Command(?)||Unconfirmed what this does, if anything|
|CNX-80 / GNS 480 WITH HS34 (ARINC - Allows GPSS Vertical Guidance)|
|Garmin GNS 480||Dynon HS34|
|P5 (78 Pin)||4||ARINC 429 Tx Channel 1A||Gamma 429 / *High||Fem D25||23||ARINC 429 RX 1A||Gama GPS / High||Unconfirmed|
|P5 (78 Pin)||24||ARINC 429 Tx Channel 1B||Gamma 429 / *High||Fem D25||11||ARINC 429 RX 1B||Gama GPS / High||Unconfirmed|
|P5 (78 Pin)||5||ARINC 429 Tx Channel 2A||VOR/ILS / *High||Fem D25||22||ARINC 429 Rx 2A||Gama Nav / High||VOR / Confirmed with v2.0; awaiting 2.3 confirmation|
|P5 (78 Pin)||25||ARINC 429 Tx Channel 2B||VOR/ILS / *High||Fem D25||10||ARINC 429 Rx 2B||Gama Nav / High||VOR / Confirmed with v2.0; awaiting 2.3 confirmation|
|P5 (78 Pin)||8||ARINC 429 Rx 2A||EFIS (Sys 1) / *High||Fem D25||24 or 25||ARINC 429 Tx||Output "On" / High||Provides encoder baro setting (and Nav course) back to 480|
|P5 (78 Pin)||28||ARINC 429 Rx 2B||EFIS (Sys 1) / *High||Fem D25||12 or 13||ARINC 429 Tx||Output "On" / High||Provides encoder baro setting (and Nav course) back to 480|
|P1 (Main)||5||RS232 TxD1 (Output)||MAPCOM 9600||Male D25||1||Serial 1 Rx||Aviation 9600||Not Required (ARINC is better) - CONFIRMED|
|P1 (Main)||4||RS232 RxD1 (Input)||SL 30||Male D25||14||Serial 1 Tx||SL 30 Command||Not required. Unconfirmed if this does anything|
- Note: Apparently either "Low" or "High" will work - just be sure that Tx and Rx speeds match. "Low" may be necessary in cases where other equipment is also receiving the same data in parallel.
Final thought: May wish to keep the serial connection for GPS even if the ARINC proves to work with v2.3, as this would provide a backup connection in the unlikely event that the wires somehow failed in flight. This can be enabled / disabled in the HSI setup so that it does / does not appear on the list of GPS sources.